45
stations. When a station with a strong signal isprogram that carries the Dolby Digital information.Delay :Press this button to begin the
CONTROLS AND FUNCTIONS
Front Paneltuned, the TUNED indicatorwill illuminate insequence of steps required to enter delay time
the Information Display. A brief(1/2 second)Dolby Pro Logic Selector : Press thissettings.
press of the button will manually tune to the nextbutton to select the Dolby Pro Logic surround
frequency increment, while pressing and holdingmode when listening to an analog orDigital Input Selector :When playing a
the button for a long period will automaticallydigital(PCM) program that is encoded withsource that has a digital output, press this button
tune to the next station with a signal strongsurround-sound information.to select between the Optical (19) and Coaxial
enough for acceptable reception.(18) Digitalinputs.
Dolby 3 Stereo Selector : Press this button
Preset Scan : Press this button toto select the Dolby 3 Stereo listening mode.Set Button :When making choices during
automatically scan through the station that haveThis mode is used primarily when a programthe setup and configuration process, press this
been programmed in the AVR-65's memory.has surround information when a center channelbutton to enter the desired setting, as shown in
The tuner will play five seconds of each stationspeaker, but no surround speakers, is installed.the information Display, into the AVR-65's
before moving to the next preset station. To stopmemory.
the scan when the desired station is heard, pressSurround Mode Selectors : Press one of
Main Power Switch :Press this button toBass Control :Turn this control to modifyinformation Display, and the red LED
apply power to the AVR-65.the lower frequency output of the left / rightabove the button will illuminate to remind youthe button again.these buttons to select the analog surroundMulti-room :Press this button to begin the
When the switch is pressed in the unit is placedchannels by as much as +/-10dB. Set thisthat you are listening to the tape monitor output.
modes. These modes may be used with anyprocess of selecting and configuring the
in a Standby mode, as indicated by the ambercontrol to a suitable position for your taste and
Preset Stations Selector : Press this buttonanalog program source to create a pleasingAVR-65's output channels.
LED.room acoustics.CD :Press this button to select the device
This button MUST be pressed in to operate theconnected to the CD Input jacks (6) as theto select stations that have been entered into thesurround effect.
unit. To turn the unit off and prevent the use ofTreble Control :Turn this control to modifylistening source.preset memory.Speaker Selector Button :Press this button
the remote control, this switch should be pressedthe high frequency output of the left / right
DTS Selector : press this button to selectto begin the process of selecting the speaker
until it pops out from the panel so that the wordchannels by as much as +/-10dB.DVD :Press this button to select the
TUN.MODE/RDS : Press this button toDTS decoding when listening to an audio orpositions that are used in your listening room.
"OFF" may be read at the top of the switch.Set this control to a suitable position for yourdevice connected to the DVD play jacks (7) as
taste and room acoustics.the listening and viewing source.select the auto or mono mode for FM tuning.video program that is encoded with DTS
NOTE :In normal operation this switch is left in
In the AUTO mode, AUTO indicator willdata.(See page 25 for more information onSelector Buttons :When you are
the "ON" position.32
Balance Control :Turn this control toVideo Input Selectors :Press one of these
illuminate in the information display, and whensurround modes and digital audio.)establishing the AVR-65's configuration settings,
change the relative volume for the front left /buttons to select a source connected to the rear
System Power Control :When the Main
right channels.panel Audio/Videoinputs (3), (16), or the frontstations are transmitting stereo signals, theuse these buttons to select between the choices
Power Switch 1 is "ON", press this button to
panelAudio/Video input.
stereo reception will be provided andStereoSurround Off : Press this button to turn offavailable. as shown in the information Display.
turn on the AVR-65 ; press it again to turn theNOTE :For proper operation of the surround
unit off. Note that the Power Indicatormodes this control should be at the midpoint, orindicator will also be illuminated in theall surround processing, and to listen to a
6-Channel director Selector :Press this
surrounding the switchwill turn green when"12 o'clock" position.
information display. In the MONO mode the leftprogram in traditional stereo from the left frontInformation Display :This display delivers
button to select the output of an optional, external
the unit is on.
6-channel decoder connected to the 6 Ch Directand right signals from stereo broadcasts will beand right front speakers only.messages and status indications to help you
Video 3 Inputs :These audio / video inputs
inputs (5) as the listening source.
Power Indicator :This LED will illuminate inmay be used for temporary connection of videomixed together and reproduced through alloperate the receiver.
amber when the unit is in the Standby mode togames, camcorder, digital still cameras or
AM/FM :Press this button to select thechannels. Select MONO for better reception ofMute : Press this button to momentarily
signal that the unit is ready to be turned on.portable audio products. To select a source
tuner as the AVR-65's input source. When it is
weak signals.silence the speaker output of the AVR-65.Remote Sensor Window :The sensor
When the unit is in operation, the indicator willconnected to these jacks, press the Video 3
first pressed the last station tuned will be heard.
behind this window receives infrared signals from
turn green.Input Selector.
Press it again to change between AM and FM
bands.Dolby Digital Selector : Press this button toVolume Control : Turn the knob clockwise tothe remote control. Aim the remote at this area
Head Phone Jack :This jack may be usedT-Mon Selector :Press this button to select
select the Dolby Digital surround mode whenincrease volume, counter clockwise to decreaseand do not block or cover it unless an external
to listen to the AVR-65's output through a pair ofthe device connected to the Tape MonitorjacksTuning button :Press the left side of the
listening to a program that carries the Dolbythe volume.remote sensor is installed.
headphones. Be certain that the headphones(24) as the listening source. The previouslybutton to tune lower frequency station and the
have a standard 1/4" stereo phone plug.selected source will continue to show in theright side of the button to tune higher frequencyDigital surround mode when listening to a
6 |
ACEC
